Yuken Hydraulic Pump, Valve, and Motor Pressure Limits Explained


Pressure mismatch is one of the top causes of hydraulic breakdowns. Run a component below its minimum pressure and lubrication fails or cavitation starts. Push it past its continuous maximum and the swash plate, piston shoes, and valve plate wear out fast. Yuken's A-series piston pumps, DSG directional valves, relief valves, and vane pumps each have their own pressure window - and the specs change between standard and heavy-duty variants.
Quick Answer
Standard Yuken axial piston pumps (A10, A37, A70) run from about 0.5 MPa minimum to 21 MPa continuous maximum, with a 25 MPa short-term peak for surge events. Heavy-duty A10H variants go to 25 MPa continuous. DSG directional valves share the 21 MPa continuous / 25 MPa peak range, with a 10 MPa low-pressure series for light duty. Relief valves adjust up to 31.5 MPa. Vane pumps need at least 0.8 MPa to avoid cavitation. Cold oil raises the minimum pressure requirement; hot oil and dirty fluid reduce the allowable maximum.
Rated Pressure vs Peak Pressure: The Difference That Matters
Most confusion comes from mixing two numbers.
Rated (continuous) pressure is what the component can hold 24/7 without accelerated wear. Running above this even for months destroys internal parts.
Peak pressure is a short-term surge limit - a few seconds when a valve closes suddenly or a load hits. The system is allowed to cross this briefly, not hold it.
A Yuken A37 run at 23 MPa nonstop for three months burned out three piston shoes and a full seal kit. That wasn't a peak event - it was continuous over-pressure, which the pump wasn't built for.
Axial Piston Pump Pressure Range
Minimum Pressure
The minimum isn't the lowest pressure the pump can make - it's the lowest inlet pressure that keeps the internal lubrication film intact. Piston pumps rely on a thin oil film between rotating parts; below 0.5 MPa on an A10-series pump, that film breaks down and you get scuffing and seal failure.
A pressure gauge on the pump inlet is the practical way to watch this.
Maximum Pressure
| Yuken pump | Continuous max | Short-term peak | Notes |
|---|---|---|---|
| A10 series | 21 MPa (3,045 psi) | 25 MPa (3,626 psi) | 10 cc/rev, small CNC and mobile power units |
| A37 / A70 standard | 21 MPa | 25 MPa | General industrial and construction duty |
| A10H heavy-duty | 25 MPa continuous | - | Built for heavy construction where regular 21 MPa isn't enough |
If your system runs regularly above 21 MPa, the fix is a heavy-duty series - not pushing a standard pump past its limit.
Directional Valves and Relief Valves
DSG Directional Control Valves
Valves don't have rotating parts relying on a lubrication film, so their minimum pressure is lower: 0.3–0.5 MPa, just enough to actuate the spool consistently. Standard DSG valves hold 21 MPa continuous, 25 MPa peak.
For light-duty systems - conveyors, small lifts - Yuken makes a 10 MPa (1,450 psi) valve series. Don't overspec: a 21 MPa valve costs more and runs noisier than a 10 MPa one in a low-pressure application.
Relief Valves
Relief valves are the over-pressure safety buffer. Standard Yuken relief valves start at 0.2 MPa minimum and adjust up to 31.5 MPa (4,569 psi) on heavy-duty models. On systems prone to sudden spikes, the relief valve setting is what protects the pump and hoses before damage occurs.
Vane Pump Minimum Pressure
Yuken vane pumps are medium-pressure units used in injection molding and similar applications. Their minimum running pressure is about 0.8 MPa - higher than piston pumps because the vanes need pressure to extend against the ring.
Running a vane pump below that causes cavitation: bubbles form, collapse on the pressure side, and erode internal parts. A client reported his pump "worked fine at 0.4 MPa" for months, then seized six months later - the cavitation had been eating the impeller all along.
Factors That Shift the Pressure Limits
Fluid Temperature
Oil below 10°C (50°F): viscosity is high, so raise the minimum pressure by about 0.2 MPa to keep flow consistent.
Oil above 50°C (122°F): oil thins out. Continuous maximum pressure drops roughly 10% once oil reaches 60°C.
Fluid Cleanliness
Yuken specifies ISO 18/15 or better. Dirtier oil scores internal parts faster at high pressure, so the allowable maximum has to come down. On one construction site where dirt got into the reservoir, an A70 pump's max pressure had to be cut to 18 MPa to stop repeated seal leaks.
A Real Case: Vane Pump Failing Every Six Months
A food processing client's Yuken vane pump failed every six months. The check showed two problems: inlet pressure held at 0.3 MPa (too low, cavitation risk) and system pressure ran at 23 MPa (15% over the 20 MPa rated max).
The fix: swap to a heavy-duty A-series pump, set inlet pressure to 0.8 MPa, and adjust the relief valve to 20 MPa. That pump ran 14 months without a single issue, and downtime costs dropped 80%. The pressure settings were the whole problem - not the pump quality.
FAQ
What's the difference between rated and peak pressure? Rated pressure is continuous duty, safe to hold indefinitely. Peak pressure is a brief surge limit for seconds at a time. Holding peak pressure continuously destroys the pump.
Can I run a Yuken A10 pump above 21 MPa temporarily? Brief surge up to 25 MPa is acceptable per spec. Anything sustained above 21 MPa needs the A10H heavy-duty variant.
Why does minimum pressure matter for valves? Valve minimum pressure ensures the spool actuates consistently. Below it, the valve can stick or respond slowly - no rotating lubrication film like a pump, but actuation still needs pressure.
What pressure should the relief valve be set to? Set it about 10–15% above the system's normal working pressure, below the pump's rated maximum. It opens on spikes, not on every cycle.
Does oil temperature affect vane pump minimum pressure? Cold thick oil needs slightly higher minimum pressure to push vanes out and keep flow. Warm up the system before high-pressure operation.
Conclusion
Yuken pressure limits break down cleanly: piston pumps 0.5–21 MPa standard, 25 MPa heavy-duty; DSG valves 0.3–21 MPa; relief valves up to 31.5 MPa; vane pumps minimum 0.8 MPa. Temperature and fluid cleanliness shift those numbers, and rated pressure is not the same as peak.
We supply Yuken A10, A37, A70, A10H piston pump parts, DSG valves, relief valves, and vane pump components. Send us your system pressure and application - we'll confirm whether your current component matches the pressure window or needs a heavy-duty replacement.






