KOMATSU KMF/KPV SWING MOTOR PARTS KMF40/90/160 KPV90/105 KPV100 SWING(PC60-6 PC120-3 PC120-6 PC200-3/5 PC220-3/5) Spare Parts For Repair Maintain
Wuhan Xinlaifu Hydraulic Equipment Co., Ltd. is one of the leading manufacturers and suppliers of komatsu kmf/kpv swing motor parts kmf40/90/160 kpv90/105 kpv100 swing(pc60-6 pc120-3 pc120-6 pc200-3/5 pc220-3/5) spare parts for repair maintain in China. With abundant experience, we warmly welcome you to buy high quality customized products at competitive price from our factory. Also, OEM&ODM service is available.
| NO | DESCRIPTION | QTY/SET |
|---|---|---|
| 1 | CYLINDER BLOCK | 1 |
| 2 | VALVE PLATE | 1 |
| 3 | PISTON | 7 |
| 4 | RETAINER PLATE | 1 |
| 5 | DRIVE SHAFT | 1 |
| 6 | CENTER BALL | 1 |
| 7 | CENTER PIN | 1 |

Komatsu KMF/KPV Series Swing Motor - Technical Specifications
| Motor Series | Machine Models | Unit Type | Function | Typical Class |
|---|---|---|---|---|
| KMF40 / KMF90 / KMF160, KPV90 / KPV105 / KPV100 | PC60-6, PC120-3, PC120-6, PC200-3, PC200-5, PC220-3, PC220-5 | 7-piston swashplate axial piston swing motor | Upperstructure rotation through swing gear | Mini to mid-size excavators |
| Part Name | PC60-6 | PC120-3 | PC120-6 | PC200-3 | PC200-5 | PC220-3 | PC220-5 |
|---|---|---|---|---|---|---|---|
| Cylinder Block | PC60-6 Swing Cylinder Block | PC120-3 Swing Cylinder Block | PC120-6 Swing Cylinder Block | PC200-3 Swing Cylinder Block | PC200-5 Swing Cylinder Block | PC220-3 Swing Cylinder Block | PC220-5 Swing Cylinder Block |
| Valve Plate | PC60-6 Swing Valve Plate | PC120-3 Swing Valve Plate | PC120-6 Swing Valve Plate | PC200-3 Swing Valve Plate | PC200-5 Swing Valve Plate | PC220-3 Swing Valve Plate | PC220-5 Swing Valve Plate |
| Piston | PC60-6 Swing Piston | PC120-3 Swing Piston | PC120-6 Swing Piston | PC200-3 Swing Piston | PC200-5 Swing Piston | PC220-3 Swing Piston | PC220-5 Swing Piston |
| Retainer Plate | PC60-6 Swing Retainer Plate | PC120-3 Swing Retainer Plate | PC120-6 Swing Retainer Plate | PC200-3 Swing Retainer Plate | PC200-5 Swing Retainer Plate | PC220-3 Swing Retainer Plate | PC220-5 Swing Retainer Plate |
| Drive Shaft | PC60-6 Swing Drive Shaft | PC120-3 Swing Drive Shaft | PC120-6 Swing Drive Shaft | PC200-3 Swing Drive Shaft | PC200-5 Swing Drive Shaft | PC220-3 Swing Drive Shaft | PC220-5 Swing Drive Shaft |
| Center Ball | PC60-6 Swing Center Ball | PC120-3 Swing Center Ball | PC120-6 Swing Center Ball | PC200-3 Swing Center Ball | PC200-5 Swing Center Ball | PC220-3 Swing Center Ball | PC220-5 Swing Center Ball |
| Center Pin | PC60-6 Swing Center Pin | PC120-3 Swing Center Pin | PC120-6 Swing Center Pin | PC200-3 Swing Center Pin | PC200-5 Swing Center Pin | PC220-3 Swing Center Pin | PC220-5 Swing Center Pin |
These swing motors are axial piston units that rotate the upperstructure through the swing gear. The rotating group combines a cylinder block, valve plate and seven pistons, held by a retainer plate, located by a center ball and center pin, with a geared drive shaft carrying the output.
We supply complete swing motors and individual replacement parts. The internal repair kit contains 7 core components: cylinder block, valve plate, 7 pistons, retainer plate, drive shaft, center ball and center pin.
Each component is manufactured to OEM specifications. Cylinder block bores are precision-honed, the valve plate is lapped for a tight sealing surface, pistons are heat-treated for wear resistance, the drive shaft gear and center locating parts are machined to original tolerances, and the center ball and center pin are matched to original fit. Parts are inspected before shipment and available for fast global dispatch, with custom OEM/ODM packaging and private-label support.
Part reference: KMF40/90/160, KPV90/105, KPV100 Swing Motor Kit

A KPV100 Swing Motor I Rebuilt for an Older Komatsu
This one came in on an older Komatsu, the kind with the -3, -5 and -6 series swing motor that also shows up as KMF40, KMF90, KMF160, KPV90, KPV105 or KPV100 across the PC60-6, PC120-3, PC120-6, PC200-3, PC200-5, PC220-3 and PC220-5 machines. The upperstructure swung slow and weak, and it drifted a little when it should have held. It wasn't seized, so I didn't treat it as a dead motor. On these 7-piston axial piston swing motors the housing usually stays intact; the loss of swing pressure comes from inside the rotating group.
I worked the pressure side first. Block and valve plate came off together, and I turned both faces over to look for where the surface had roughened or gone out of flat, reading the actual wear marks instead of chasing one obvious break. The seven pistons in those bores follow the same pattern, one edge rubbing harder than the other. The retainer plate behind them keeps the set seated in the ball guide area, and on this machine it hadn't shifted, so it went back in.
The center ball and center pin are what locate the group, and the drive shaft carries the geared output. I checked the ball for flats or shine, the pin for bending or scoring, and the gear teeth on the shaft for wear. The ball was still round and the pin hadn't bent, so both stayed; the shaft gear showed no bad tooth, and it went back as well.
That part-by-part call is how I keep these rebuilds honest. The block, plate and pistons don't wear at the same rate, so I don't swap the whole swing motor on habit. Anything still within original tolerance stays, and I change only what the bores, faces and locating parts actually show worn. If the plates and pistons measure fine but the motor still slips or drifts under load, I go back to the locating and output parts before calling the motor a total replacement.
The same axial piston swing layout turns up on other makes' excavators - Rexroth, Sauer, Komatsu, Hitachi, CAT, Kawasaki, Linde, Eaton Vickers, Parker, Nachi, Uchida, Yuken, Liebherr, Toshiba, Kayaba, Oilgear, Denison, plus Doosan, Volvo, Hyundai, Foton and Kato machines - but each swing motor's wear has to be judged on its own.
FAQ
WUHAN XIN LAI FU HYDRAULIC PNEUMATIC EQUIPMENT CO.LTD
Q: Is there a customization option available? For example, OEM/ODM?
A: Yes, We can provide customized services.
Q: Can you make my own brand on the products?
A: Of course we can.
Q: How to obtain a detailed quotation?
A: Mobile,Whatsapp,Wechat: +86-18995500394
Mail :kate_bao@rexroth-hyd.com
Q: What is the MOQ?
A: Determine MOQ based on your product, standard product: MOQ 1pc, non-standard: 10-500pcs
Q: What payment methods are supported?
A: TT/PayPal/Western Union/Credit Card/Bank Transfer
Q: What is your payment terms?
A: Sample order,full payment in advance;full order,30% /50% deposit and the balance before shipment.
Q: How long is the delivery time?
A: Spot products are expected to take 2-3 working days, while futures products are determined based on the delivery time.
Q: How long does the warranty ?
A: Warranty 12 months
Q: Does your company have ISO certification?
A: Yes , we have
Q: Can you provide samples?
A: Yes , we can supply sample ,but not free .
Contact with me pls if you have other questions!
I am waiting for your good news!
Best regards,
Kate bao
Mobile,Whatsapp,Wechat: +86-18995500394
Mail :kate_bao@rexroth-hyd.com

Hot Tags: komatsu kmf/kpv swing motor parts kmf40/90/160 kpv90/105 kpv100 swing(pc60-6 pc120-3 pc120-6 pc200-3/5 pc220-3/5) spare parts for repair maintain, China komatsu kmf/kpv swing motor parts kmf40/90/160 kpv90/105 kpv100 swing(pc60-6 pc120-3 pc120-6 pc200-3/5 pc220-3/5) spare parts for repair maintain manufacturers, suppliers
Previous
No InformationNext
No InformationYou Might Also Like
Send Inquiry












